D-Link DWL-8200AP REV B 802.11a/g Managed Dualband Access Point Firmware

Do NOT upgrade firmware on any D-Link product over a wireless connection.

Failure of the device may result. Use only hard-wired network connections.

What's New:

Problem Resolved:

[SNMP] dot11SecAccountingServerPort node cannot get value.

[WEB] When VLAN state is enabled, change the MSSID’s security will disable MSSID’s state.

[Firmware] STA couldn’t connect to multi-ssid of 11a band when eth, wlan0, wlan1 use the same mac address. So change the mac address rule back to original

[Firmware] It should send an IAPP-ADD-Notify packet when STA roaming to AP2 from AP1, not only an IAPP-Move-Notify packet.

[Firmware] Change the MAC address rule, eth, wlan0, wlan1 use the same mac address.

[SNMP] Fix SNMP show "00:00:00:00:00:00" mac address in 11A band.

[MIB] Support WDS client info.

[FW] Intel WiFi Link 4965AGN can’t connect to AP if authentication is WPA/WPA2 PSK, and vlan state is enabled.

[FW] Fix the Microsoft SilverlightIE compatibility issue.

[FW] AP couldn’t connect to fast radius.

[FW] Modify the channel list in 11a band for U3 domain.

[FW] Enhance the MSSID over WDS function, allow user change the security settings of MSSID when the ap mpde is WDS with AP.

[FW]Support maximum community string length to 32 characters.

[WEB] The Vlan tag mode should be set to Manual when Authentication is not WPA in multi-ssid page.

[WEB] If enable Vlan state when the AP mode is WDS, it should pop up a warning message.

[WEB] AP will crash if save Rouge AP detection info before the Radar scan complete.

[WEB] User can’t configure a valid IP address(such as X.255.X.X or X.X.255.X) as a DHCP Start Address in DHCP Server page.

[FW] A/G band IGMP snp cannot play simultaneous

[WEB] The dynamic vlan mode can not set successful on the multi-ssid page of 802.11a.

[WEB] If set the authentication to WPA-EAP, the multi-ssid page display imperfectly.

[WEB] User can’t set Wireless MAC ACL.

[WEB] If ap mode is not normal ap, then Grouping should be gray and can't set.

[WEB] Enable VLAN State when the multi state is disabled, the radio button of band should point to “both”.

[WEB] There should be a warning message, when changing primary ssid’s authentication will affect MSSID’s authentication.

[CLI] When WDS or WDS with AP mode is set, disable CLI command about ratecontrol and supportrate.

[FW] Only permit user manage the ap through Lan1.

[FW] Mssid over WDS function has some conflict with Mssid Eth to WM filter policy, it won’t take effect if the Mssid Eth to WM filter policy is enable.

[FW] Broadcast packets may miss four bytes if Vlan is enable, this will cause two station can not communicate between 802.11a&802.11g on the same vlan.

[FW] Trap can’t send.

[FW]When MSSID is enabled and authentication type is WPA-PSK in secondary SSID, the STAs which associated to secondary SSID failed to ping each other.

Enhancements:

[FW] Support APMII v2.0.

[FW] Modify the channel list in 11a band as the latest output power table sepc.

[FW] Support NAP function based on dynamic vlan.

[FW] Support Primary SSID with VLAN tag function

[FW] Support Administration VLAN(Manage VLAN) , administrate AP with WLAN and management IP range function

[FW] Trap server settings(categorize the types of traps)

[FW] Support MSSID over WDS

[FW] WMM over WDS

[FW] Priority by SSID

[FW] IGMP Snooping (v1/v2)

[FW] 802.1X Dynamic VLAN

[FW] Data Rate Control follows Dlink new spec.

[FW] Support IAPP (fast roaming)

[FW] Enable/Disable ping

Secondary RADIUS server setting

[FW] AP status on UI (also on MIB)

CPU and Memory utilization

Statistics for Ethernet TX and RX bytes and packets

[WEB]SSID change wireless network name (SSID)

[MIB]Support 802.11MIB

[MIB]Support MIB-II (RFC-1213)

[MIB]Support Trap002-1 spec

[CLI] CLI command to input SNMP Location.

[CLI] Hide the commands, get targetPower/gett controlPower/get swPower , in CLI

[CLI]Open 3 RSTP commands, rstp getstp/rstp getstate/rstp setstate